linkedin
punkt1 punkt2 punkt3 punkt4 punkt5 punkt6 punkt7 punkt8 punkt9 punkt10 punkt11 punkt12 punkt13 punkt14 punkt15 punkt16 punkt17 punkt18 punkt19 punkt20 punkt21 punkt23 punkt24

Tanks

Surface rebuild after erosion, corrosion or bi-metallic corrosion. Coating of reconditioned surface areas. By repair of leaking tanks, the best result is obtained by repairing on the pressure side. At leaking tanks, it is often seen that the corrosion has spread out in the surrounding area, it is therefore recommended to check this before starting the operation.

Risers

Surface rebuilding after erosion, corrosion or bi-metallic corrosion. Coating of reconditioned surface areas. Materials used below water surface or splash zone above water are UW (Under Water products).

Coolers

Surface rebuilding and coating after erosion, corrosion or bi-metallic corrosion at end covers.

Pumps

Surface rebuilding after erosion, corrosion or bi-metallic corrosion. Coating of reconditioned surface areas.

Valves

Surface rebuilding after erosion, corrosion or bi-metallic corrosion, Coating of reconditioned surface areas.

Sea water Pipes

Emergency repair of leaking pipes and flanges. Long term rebuilding of wall thickness

Freshwater Generator

Surface rebuilding and coating after erosion, corrosion or bi-metallic corrosion.

Manifolds, pipes, cylinder liners etc.

Rebuilding of shapes, contours and material thickness of most engine parts and repair of cracks in engine housing. Coating of repaired items.

Anchor Winch

Surface rebuilding after abrasion, erosion or corrosion. Coating of reconditioned surface areas.

Sea water Pipes

Emergency repair of leaking pipes and flanges. Long term rebuilding of wall thickness.

Bov Thruster

Surface rebuilding after abrasion, erosion or bi-metallic corrosion at tunnel or unit. Coating of reconditioned surface areas.

Sea water intake and filters

Surface rebuilding after erosion, corrosion or bi-metallic corrosion. Coating of reconditioned surface areas.

Crane, Swivel ring, Hydraulic Rams

Fixing gaps between flange and swivel ring to mate the surface of the flange. Damages caused by poor machining, distortion from welding, corrosion or bi-metallic corrosion.

Pumps, Valves

Surface rebuild after erosion, corrosion or bi-metallic corrosion. Coating of reconditioned surface areas.

Steam pipes or cable pipes on deck

Emergency repair of leaking pipes and flanges. Long term rebuilding of wall thickness.

Anti Skid protection, deck corrosion

Wencon Coating and aggregate are used to ensure non-slip surfaces on deck, floors, steps, stairs, passages etc. For corrosion protection of deck only, no aggregate is used.

Heating coils

Heating coils often leak in the welding sleeve joints, due to use of improper welding material. Heavily pitted pipe surfaces are often seen in the bottom area, usually caused by the combination of bad steel – aggressive media - and high surface temperature.

Ballast tank corrosion

Steel constructions near the inlet of a pump often suffer from erosion/corrosion and impingement, for instance the ballast tank. In case the deterioration has reached a point, where thickness of the steel plates are critical small, doublers should be welded in before this treatment.

Tank corrosion, Cargo/Bunker

Surface rebuilding after erosion, corrosion or bi-metallic corrosion. Coating of reconditioned surface areas. By repair of leaking tanks, the best result is obtained by repairing on the pressure side. At leaking tanks, it is often seen that the corrosion has spread out in the surrounding area, it is therefore recommended to check this before starting the operation.

Ballast water Pipes

Emergency repair of leaking pipes and flanges. Long term rebuilding of wall thickness.

Valves, Flanges, Shafts, bearings, endcovers, manifolds etc.

Rebuilding of shapes, contours and material thickness of most engine room parts. Coating of repaired items.

Pipes

SKAL SLETTES

Propeller

Rebuilding the shape of propeller with cavitation spots and finishing with thin layer of coating.

Rudder couplings, rudder stock bushing seats etc.

Rebuilding the shape of rudder with cavitation spots and finishing with thin layer of coating. Rebuilding or casting of bearing parts and pins with bi-metallic corrosion.

Where to use Wencon Products

To see where Wencon products can be used, please point your mouse at the orange points

    LET'S GET IN TOUCH

    Write your details and we will be back to you as soon as possible